Home > Not A > Not A Switching Port Error

Not A Switching Port Error

Contents

Try for Just $1. SwitchA(config)#interface fa0/14 SwitchA(config-if)#switchport mode trunk Command rejected: An interface whose trunk encapsulation is "Auto" can not be configured to "trunk" mode. Rene is also quick to reply to topics posted in the various forums. Join Us! *Tek-Tips's functionality depends on members receiving e-mail. http://themedemo.net/not-a/not-a-switching-port-error-message.html

ISCSI network cards for our servers require special setups to our 3560 switches.I have the configuration in place I just have an issue with this one g0/2 port which is being This is completely normal because the show vlan command only shows interfaces in access mode and no trunk interfaces. Visitor Map Feedjit Live Blog Stats Visitor from .. Thanks, SV May 29, 2015 at 08:49 #15326 Rene MolenaarKeymaster Hi SV, I can't think of any good reason to use dynamic auto or desirable.

Switchport Mode Trunk Command Rejected Not A Switching Port

Figure 2 Usage This is the total usage on this switch port, over the previous thirty seconds. Let’s see what options we have: SwitchA(config-if)#switchport trunk encapsulation ?   dot1q      Interface uses only 802.1q trunking encapsulation when trunking   isl        Interface uses only ISL trunking encapsulation when trunking   I have a feeling of being well prepared and ready to take my test. vlan 50 name Computers !

  1. I have this problem too. 0 votes 1 2 3 4 5 Overall Rating: 5 (2 ratings) Log in or register to post comments Replies Collapse all Recent replies first sundar.palaniappan
  2. The Best Dollar You've Ever Spent on Your Cisco Career!
  3. Becky posted Oct 17, 2016 at 5:43 PM Roccat Skeltr Smart RGB Gaming...
  4. Technically the interfaces between the two switches can also be in access mode right now because I only have a single VLAN.
  5. Russ Johnson, Oct 16, 2003, in forum: Cisco Replies: 0 Views: 2,309 Russ Johnson Oct 16, 2003 Catalyst 6509 VLAN and SNMP question Martin Haberstroh, Nov 4, 2003, in forum: Cisco
  6. access-vlan DATA; # .... [...
  7. interface FastEthernet0/14 switchport mode trunk switchport trunk encapsulation dot1q !

Answer 724 (100.0% helpful) Supervisor Engine is running in IOS mode and not native or hybrid mode. SwitchB(config-if)#switchport mode ?   access        Set trunking mode to ACCESS unconditionally   dot1q-tunnel  set trunking mode to TUNNEL unconditionally   dynamic       Set trunking mode to dynamically negotiate access or trunk   Every lesson is set up in a way that makes learning interesting and fun. Either Port Is L2 And Port-channel Is L3, Or Vice-versa Depending on the switch model you might see the same error as me.

Rob Cain Network Engineer Fast & Complete! Command Rejected Po2 Not A Switching Port and to convert that layer 3 port back into layer 2 port you need to fire the command "SWITCHPORT" under perticular interface...regardsDevang See More 1 2 3 4 5 Overall Rating: When I try to put an intyerface in to a vLan switchport access vLan x I get the "Gigabit Ethernet x/x not a switching port". interface FastEthernet0/2 switchport access vlan 50 !

Close Box Join Tek-Tips Today! May 29, 2015 at 08:43 #15325 Srinivasan CParticipant Hi Rene, Network operators knows which ports are connected to switch and hosts. end SwitchB hostname SwitchB ! SwitchB#show interface fa0/14 trunk Port        Mode             Encapsulation  Status        Native vlan Fa0/14      on               802.1q         trunking      1 Port        Vlans allowed on trunk Fa0/14      1-4094 Port        Vlans allowed and active in management domain Fa0/14     

Command Rejected Po2 Not A Switching Port

care to explain why its Limited? Unanswered Question acameron12 Jan 29th, 2007 Trying setup a 3550-48.The following command::int fa0/1switchport mode dynamic desirableIs responded to with:Command rejected: Fa0/1 not a switching port.Command rejected: Fa0/1 not a switching port. Switchport Mode Trunk Command Rejected Not A Switching Port You can see if an interface is in trunk mode, which trunk encapsulation protocol it is using (802.1Q or ISL) and what the native VLAN is. Command Rejected: Not A Convertible Port. Port Overview The Switch Ports section shows a basic view of the status on all switch ports.

For instance - setting a port as an access port - if not explicitly set, it appears to be the default. I’m going to play with the switchport mode on SwitchA and SwitchB and we’ll see what the result will be. No, create an account now. I thought i would push on and get some vLans set up etc to see how far we could get. An Interface Whose Trunk Encapsulation Is Auto Cannot Be Configured To Trunk Mode

Consider these outputs: [email protected]# show interfaces xe-0/0/47 | display set set interfaces xe-0/0/47 unit 0 family ethernet-switching [edit][email protected]# commit commit complete [edit] [email protected]# run show vlans default detail VLAN: default, Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More... They can configure access mode or trunk mode accordingly. I do have a follow up question.

The visual port state displays information in the following ways: Display Icon Explanation Link operating at full 1Gbe (or 10Gbe on SFP+ ports) Link operating at reduced speed/duplex (10 or 100mbps) Thanks! I recommend it to everyone!

Herman Janson Network Engineer THE Go-to Resource!

After a couple of minutes of searching, this is what I found: In switches that support both L3 interfaces and L2 switchport, the message Command rejected: [interface] not a switching port It's a good site for beginners and also for seasoned network engineers. He also gradually takes you to the more involved section. I will then post the results of the commands.At this time I'm traveling to another office so I'm away from the switches.regards. 8 posts Ars Technica > Forums > Hardware &

Template images by luoman. all subhierarchies of the config, thats why you start with interfaces in the first place and do wildcard the interface name), which is because you can use apply-groups on ALL levels This won't be a working trunk but I think the access mode VLAN (VLAN1) will work. Look forward to upcoming updates!

thejayman wrote: > Hi all, > Need a bit of you expert advise on the 6509 I have just got my mits on. > First of all, I have connection via Port consistency restored. Previous Lesson802.1Q Encapsulation Next LessonHow to change the Native VLAN Home › Forums › How to configure trunk on Cisco Catalyst Switch This topic contains 36 replies, has 21 voices, and See More 1 2 3 4 5 Overall Rating: 0 (0 ratings) Log in or register to post comments franklaszlo Tue, 01/30/2007 - 04:17 Hi,the only thing I can think of

The Net packet packet packet Pages Home Wednesday, April 21, 2010 Command rejected: Po1 not a switching port on Cisco Catalyst 4500 check the etherchannel status SW1#show eth sum Flags: D Just click the sign up button to choose a username and then you can ask your own questions on the forum.